SECTION 09805 COAL-TAR EPOXY COATING SYSTEMS FOR STEEL TIE RODS AND ACCESSORIES PART 1 - GENERAL 1.01 SCOPE:The Work of this Section shall consist of furnishing all labor, materials and equipment necessary for installation of coal-tar epoxy coating systems for steel tie rods and accessories as shown on the Drawings and specified herein.
100% SOLIDS COAL TAR-BASED EPOXY COATING10 Coal Tar Epoxy in temperatures below 50º F or to frozen, frost filled or damp surfaces. Keep away from heat, sparks or open flame. WARNINGS:Use with adequate ventilation. G10 Coal Tar Epoxy contains an alkaline amine. Avoid breathing vapors and prolonged contact with the skin. Wear protective clothing and safety glasses during application.
Our ERW pipe is available in standard, schedule 40, schedule 80 and unscheduled size options. ERW Line Pipe Features:Available sizes:2 3/8 in. 24 in. outer diameter (OD) See chart below for a full list of dimensions. Grades:API 5L B, X42, X52, X60, X65, X70; Specifications:ASTM A53
Amercoat 78HB - Pipe Industries Corporationair 40 to 122 4 to 50 surface 40 to 120 4 to 49 78 Series Amine-cured coal-tar epoxy Amercoat. Surface Preparation Coating performance is proportional to the degree of surface See Recoat and Repair Schedule. The surface must be clean and dry when repair coat is applied. 12. Inside tanks, pipes and other confined ar eas, ventilate during
Amercoat 78HB - Pipe Industries Corporationcoating must be fully cured according to the schedule. These times are for a thickness of 16 mils (400 microns). For greater thickness, allow additional time. Drying and cure times (ASTM D1640) °F/°C 90/32 70/21 50/10 touch (hours) 3 12 6 2 1212 through (hours) 10 15 12 48 recoat (maximum, hours)1224 72 cure before service (days) 141028
2 cts. Corothane I Coal Tar 5.0-7.0 (125-175) Concrete, smooth:2 cts. Corothane I Coal Tar 5.0-7.0 (125-175) On previously painted concrete, spot prime bare areas with Coro-thane I Coal Tar reduced 10% with Reducer #15, R7K15. Check compatibility. The systems listed above are representative of the product's use, other systems may be appropriate.
B65B11 - paintdocs2 cts. Corothane I Coal Tar 5.0-7.0 (125-175) Concrete, smooth:2 cts. Corothane I Coal Tar 5.0-7.0 (125-175) On previously painted concrete, spot prime bare areas with Coro-thane I Coal Tar reduced 10% with Reducer #15, R7K15. Check compatibility. The systems listed above are representative of the product's use, other systems may be appropriate.
Coal Tar Coating and Wrapping of Underground Pipelines Jan 02, 2020 · Coal Tar Coating And Wrapping of Underground Pipelines. This blog covers the basic information about procedure for coal tar coating and wrapping of underground pipelines including, minimum requirements for materials cleaning, priming, coating & wrapping, inspection and testing of Coal tar coating to be provided on the field joints of underground steel lines.
COAL TAR EPOXY COATING Coal Tar Epoxy - Two Component - 100% Solids Product #209 PRODUCT DESCRIPTION Coal Tar Epoxy Coating Product #209 is a two component 100% solids epoxy coating designed for applications to petroleum contaminated concrete, coating asphalt based surfaces, clean concrete, cement, and properly prepared steel. LIMITATIONS
Epoxy-Polyamides - an overview ScienceDirect TopicsCoal-tar epoxy-polyamide black or dark red paints are hazardous because of their flammability and potential toxicity, so proper safety precautions should be observed. Safe handling practices are required and should include, but not be limited to, the provisions of SSPC-PA Guide 3, A Guide to Safety in Paint Application, and to the
Industrial 4.72 TARGUARDCOAL TAR EPOXY PART A B69B60 B LACK PART A B69R60 R ED PART B B69V60 H ARDENER Industrial & Marine Coatings Concrete, atmospheric or immersion:2 cts. TarGuard Coal Tar Epoxy @ 8.0 - 16.0 mils dft/ct Steel, atmospheric or immersion:2 cts. TarGuard Coal Tar Epoxy @ 8.0 - 16.0 mils dft/ct Steel, atmospheric or immersion:1 ct. Copoxy Shop Primer
ASIAN COAL TAR EPOXY PAINT Coal tar epoxy coating PROTECTIVE COATINGS Two component, high build coal tar epoxy coating blast cleaned to Sa 2.5 of Swedish specification approx. 1.40 ± 0.05 kg/ ltr (depending on shades) 20 ltrs (Base :16 ltrs & hardener :4 ltrs)
PROTECTIVE COATINGS ASIAN COAL TAR EPOXY PAINTASIAN COAL TAR EPOXY PAINT Coal tar epoxy coating PROTECTIVE COATINGS Two component, high build coal tar epoxy coating blast cleaned to Sa 2.5 of Swedish specification approx. 1.40 ± 0.05 kg/ ltr (depending on shades) 20 ltrs (Base :16 ltrs & hardener :4 ltrs)
Paint Adhesives & Coating Pioneer Metal FinishingEpoxy Paint. Epoxy spray coatings provide the same level of corrosion protection as standard E-coat processes while offering the advantages of cost effective part masking.Our automated chain on edge system allows mass production and uniform coverage of the epoxy paint. Pioneer offers a wide variety of pretreatments and primers that can be combined with top coats to achieve high performance
Coal Tar Epoxy Experience on Houseboats by:O ld Houseboater I utilized Coal Tar Epoxy on 2 RiverQueens, 2 KingsCrafts, and 1 Pluckebaum. I checked condition on the steel boats every 2 years, on the aluminum boats every 3. Other than scrapes I never had any peel off. I had mine sand blasted prior to application in all cases.
SPECIFICATIONS - DETAILED PROVISIONS Section P5 Coal Tar Epoxy Amercoat 78 Carboline Bitumastic 300M Tnemec 413 P6 Coal Tar Mastic Carboline Bitumastic 50 P7 Universal Primer Carbocrylic 120 Amercoat 38 Tnemec 77 Chem-Prime P8 Grease Chevron E.P. Roller Grease or Texaco Rust Inhibitive Grease P9 Epoxy Amercoat 74 Carboguard 890 Tnemec 66 P10 Vinyl Wash Primer Amercoat 59
York County Government Standard Details(ii) Coal tar epoxy lining 24 mils (dry) minimum dry film thickness and shall be Koppers No. 300M, Americoat No. 78, Carboline-Carbomastic No. 14 or approved equal. e. The outside of steel pipe and complete couplings shall receive one coat of Koppers 300M coal tar epoxy - 16 mils minimum dry film thickness - or approved equal.